Last Friday I finished all of the bed moulding trim work in the living room. All that’s left is to fill nails holes–about a billion of them.
Over the last three days, it’s been my mission in life to complete building the beams and installing them in the living room. The final verdict? — Done. The journey? Abysmal! If I had had a crew of four or five able-bodied hands, it would have turned out much better than it ultimately did. That being said, it’s passable by most standards and so I’ll let it go.
The general construction was a three-sided, tongue-and-groove box stabilized a bit by adding glue blocks. The large boxes that covered the I-beams had a pine 1x cut to a 45 degree angle attached to the top. (photo #2) Screws were then used through the pine into the ceiling. This was effectively the only way to attach it since it couldn’t be attached to the beam itself. The perpendicular boxes were nailed to a 2x that was bolted to the ceiling. (photo #3) The trim is bed moulding which will be supported by the pine piece.
The triangle-shaped section over the fireplace had a really tricky angle, but with a jig and a couple test cuts, I was able to get it pretty darn close. (photo #7)
The refurbished, vintage light (with modern glass) really adds to the room. My sincere thanks goes out to Seth for graciously supplying it.
Hopefully, trimming can be done on Saturday…
Life… Time… Money… Motivation… All valid excuses that have no bearing on the present.
The last child is about to stretch her wings into adulthood by graduating from high school. With the reception looming in the near future, it seemed prudent that the dusty, crusty I-beams in the living room needed to be covered at long last. A couple weekends ago, I finally got started by putting a “frieze” of quartered oak boards around the perimeter of the room.
This past Friday, I got the caps and moulding added to the two windows. They’ve looked bare and forlorn for so long now. The space above the windows was very tight–right at six inches. The caps were installed using finish screws. As I was backing out one of them over the large, cottage window, the drill got away from me and punched a hole in the ceiling. No huge deal, but just another setback in the timeline.
And finally, the interior beams are now ready to be cut to length and assembled. They will be tongue-and-groove joint boxes and attached to the ceiling in two different ways. More to come on that…
About a month ago, I installed the upper sash in the living room window. It only took a few days to start and finish it–another one of those “why didn’t I just do this in the first place?” moments. I have no official plans to start another one anytime soon.
It will probably be spring before I finish the ceiling in the living room, so now seemed like a good time for a trip down amnesia lane for this project. The pine mantel will be replaced with an antique oak mantel with mirror hopefully early next summer. It’s in pieces and some of it still needs to be stripped of a million layers of paint.
Another quick update on the living room progress. Very slow going, but forward movement nonetheless. Soon I’ll have no excuse to put off working on the ceiling beams…
Except for around the fireplace, the baseboard and chair rail are complete. Today, the first of the picture rail went up. The head casing over the two doorways will be a little challenging because they aren’t flush with the wall. Still ruminating on the best way to resolve that problem so it doesn’t look too trashy.
The plinth blocks, base cap, chair rail, picture rail, and egg-and-dart were purchased. I’ll buy the baseshoe as well one of these days. Everything else was milled, including the trim, sills, and ogee window stops.
No more talk of tile for a bit…
Time to catch up on a few items. I think I am done, for the most part, with staining. I’ve moved on to installing the trim in the living room. It’s slow going since I opted to avoid the nail gun to hang the trim. Because it’s all quartered oak, I was afraid it would split if I drove a nail into it, so I reverted to the old fashioned method–pre-drilling, nailing, and setting by hand. To top it off, I’m obsessive-compulsive about the joints, so I spend far too long (perhaps) trying to make it “just right”.
There are “crowns” for the door and window trim along with some egg-and-dart moulding, but I haven’t quite gotten to that yet.
All but three pieces of trim in this room will be newly made.
All of Sunday was devoted to planing, staining, and sealing some of the quartered oak. I started with what will become the baseboard, cap, and chair rail. The next step is to go over it with a dark walnut gel stain. I can’t wait to see what that ends up looking like…
Time to catch up. The living room and bathroom are painted and outlets and switches installed. Lots more work to do to trim it out. The trim in the living room will all be quarter-sawn oak. I bought some new and will be recycling some old as well. When I went to grad school, the university went through the process of replacing all the doors in the main administration building with “fire-proof” doors. Apparently the old ones weren’t up to code. The real shame was that the old ones were all 8-foot tall, 2-inch thick, quartered white oak with solid raised panels. I bought three of them at the time and they’ve been in storage ever since. I decided now was the time to put them into service. They will become part of the new beamed ceiling.
At first, I was going to strip them, but then reconsidered and ran them through my planer. Although the rails and stiles were veneered, the veneer is at least 1/8th of an inch thick. It worked beautifully and was so much faster. Not to mention that they are now raw wood and should take the stain and finish like all the rest. Even after I split them in half, they will be about an inch thick. I wonder how old the trees were that were made into these doors 110 years ago?
The living room paint is not what was originally planned. My wife insisted that she wanted red, so the lowest portion was made red. It looked like a crime scene. My daughter’s first reaction was, “It looks like someone painted the walls with blood!” It took my wife two days to finally decide it had to go. This works so much better. It’s brown, but it’s not red!
This morning, I stripped the bathroom window and sash front and back. About four or five layers of paint are now gone. The primer and top coat have been applied to the exterior. Next I will dig out what remains of the paint on the interior, stain, and finish them.
I’m tired already and I’ve just barely started…
And the bathroom tile is scheduled for Tuesday. I’m as happy as a tornado in a trailer park!
Painting, painting, painting. I’ve primed all of the walls and painted the ceiling of both the living room and bathroom. The bathroom will be boring white, but the living room will have color on the ceiling to make it feel a little warmer. There are two more colors for the living room and a LOT of oak trim yet to be fashioned. Painting was always the downward slope for past projects but in some respect, I’m just getting started with this one.